Wednesday, November 2, 2011

Process sequence of cutting section in apparel garments industry

Process sequence of cutting section in apparel garments industry



Store
Fabric Fault Checking
Relaxation
Shade Checking
Prepare the fabric in the fabric spreading m/c
Spreading
Marker attachment
Cutting
Numbering
Bundling
Panel Check (QC)
Fault
←     ↔    →
OK
Replace Cut
→     →      ←    ←
Solid
←     ↔    →
Not Solid
Print / Embroidery
→     →      ←    ←
Checking & Counting (QC)
Sewing









Store of Garments:
Garments store is the sector where all the raw material are stored which are need to make a garments. Raw fabric for cutting, which will be processed to garments by cutting, sewing, is kept here until the process starts. This fabric comes from the main factory after knitting and dyeing. Different types of fabrics like Single Jersey, Lycra, fleece, rib etc. There are three sections, Fabric Store, Garments Store, and General Store. In Fabric store all the fabric is being stored. In Garment store, all the items without fabrics that are needed to produce garment is stored. Finally, in General store, all the related things that is needed to run a factory is stored.

In fabric store, normally 250-300 ton fabric comes to store in each day. Now, around 37 ton fabrics are stored. Few days ago, this number was around 100 ton. Cutting department get fabrics from here. There is a Fabrics Requisition sheet where all the information is being written about the fabrics movement from store to cutting section.


Fabric Fault Check out before cutting:
This quality control section is very important before garments cutting. The fabric is roughly checked from dyeing section and then those are sending to garments factory for producing complete garments. Usually very small amount of fault comes from dyeing. Small hole and pin hole are the main fault get in cutting quality check. But a single pin hole in single part of garment could be the cause of rejection of garments and it is a major defect. That’s why a thoroughly checking is done before cutting. Here Fabrics are being checked before going to relaxation section of cutting. Required number of table is preserved for fault checking. Fabric fault like hole, yarn miss, dart etc are being checked. Normally 10% fabric is checked. There are two popular fabric fault checking system is exist. Ten point system and four point system. Usually four point system is very much popular for knitted fabric and ten point system is popular for woven fabric.


Relaxation of fabric for cutting
Normally Fabric came in a roll form. Before sending the fabric for cutting, it is necessary to relax the fabric. Usually fabric comes as the form of role or gathered from textile dyeing section. So the dimensional stability of fabric is relatively lower and it contain crease mark. The fabric is kept in an open place for around 12-24 hours according to fabrics type and buyer requirements. Relaxation time for lycra fabric and pique fabric is around 3 days and minimum 24 hours. For Single Jersey and Fleece fabric, standard relaxation time is 24 hours and minimum time is 12 hours. There are racks to store the fabrics for relaxation.


Shade Checking before cutting:
Shade checking is most important part in cutting section. Before spreading the fabric on the cutting table, relaxed fabric is rechecked for shade variation in time of relaxation. If the fabric is ok then it goes for cutting. If not, then that part of fabric is rejected and transferred for further reprocessing. 

Prepare the fabric in the fabric spreading m/c
The fabric is being gathered in the machine in a small lay form that will be easy to spread the fabric in the fabric cutting table. At least two men are needed to do the job.

Spreading of fabric:
Fabric is spread on the table by spreader machine. One man control the machine and around 6-10 people to adjust the fabric to its specific dimension. Number of layer varies according to the marker length and production needed. More the layer length will be, the more will be the production rate.

Marker attachment
After laying down the specific number of fabric on the cutting table the marker paper is over laid on the fabric. Then the marker paper is attached to the fabric  by some adhesive. 

Cutting
There are cutting man to cut the laid fabrics according to the marker sketch. Normally two men do this job. Generally 10-15 number of laid fabric is being cut.

Numbering
The fabric peaces are being numbered by a labeling machine to identify these peaces in future.

Bundling
All the numbered fabric is then bundled together and send it for checking.

Panel Check (QC)
Here, the fabric is being checked for any fault. There is a sticker with all the information that is needed to identify this bundle in future for further processing like, Date, Buyer, cutting no., size, bundle no, quantity, serial no., color, lot no. In checking normally Cutting no., size, serial no. are checked.

After Panel Check
If there is a fault in the fabric then it send for further processing. If there is some spot in the fabric then it will be washed and if there is hole or some thing that needed to be replaced then is send for replace cutting.

If the garment will be solid then it goes for sewing. But if some fabric peaces needed to be printed or embroidery then it goes for it. After returning from printing or embroidery the fabric is ready for sewing.  

Checking & Counting (QC)
After doing, the entire job in cutting section the fabric is checked and counted. Then, all these peaces go for sewing. Responsible people from sewing department receive the fabric from cutting department.

Sewing
Now, the peaces of fabrics are joined together to make the final product.


1 comment:

  1. Its so effective post for textile related parson. SO nice post.
    www.speedreply.com

    ReplyDelete